AeroBeez.com

Aerobeez 78″ Slick 540 Typhoon Build Log

A few things to note before moving on. This plane comes pre-hinged with the exception of the rudder (like most kits this size). We know that some pilots prefer to hinge the plane as people have been concerned about throw, but all we can assure you, that is not the case here. Our factory has done a […]

Building Tip of the Week: EPP Aircraft Easy Repair

Hey pilots, welcome back for another installment of Pete’s Tip of the Week! This week is a wild week with Joe Nall and RCX. We are looking forward to seeing everyone at both shows and giving everyone a close up look at all of our models including the new EPP lineup. This tip today will […]

Building Tip of the Week: Slotting CA Hinges

Hey pilots, welcome back for another installment of Pete’s Tip of the Week! If you are not familiar with CA hinges, this tip will help you see a good way to install them and if you are familiar, we hope this helps you improve how you already install them. So without further ado, today’s tip […]

Building Tip of the Week: 4Titude Fuel Tank Mod

Good day pilots and welcome to another installment of Pete’s Tip of the Week!  In today’s tip, we will be installing a 4Titude fuel tank in place of the stock fuel tank onto our Aerobeez 65″ Yak 54 Profile ARF! These same steps can also be used on our 65″ Extra 330 Profile ARF or […]

Building Tip of the Week: Cutting the Servo Bay

Hey pilots, happy hump day and welcome back for another installment of Pete’s Tip of the Week! Today we will be looking at the servo bay and walking you through a simple way to cut out the skin while leaving a portion to seal the edge. This method helps prevent pealing of the skin and […]

BuildingTip of the Week: Installing CA Hinges

Hey pilots, welcome back for another installment of Pete’s Tip of the Week! 2015 has been crazy busy with shows and new products, so we took a few weeks off from this series, but are happy to bring you a new tip today! If you are not familiar with CA hinges, this tip will help […]

Building Tip Of the Week: Adjusting Control Surface

Hey pilots, welcome back for our first installment of Pete’s Tip of the Week for 2015! This week has been a busy week leading up to the AMA Expo. We have been busy building our new models for the show and putting together all the final details for our new models that will be unveiled […]

Building Tip of the Week: Cowl Ventilation

Hey pilots, welcome back for our final installment of Pete’s Tip of the Week for 2014! Tonight will be a night of celebration and we hope you all ring in the New Year with friends, family, loved ones, and possibly a new build project! Today’s tip will be dealing with cowl ventilation and will hopefully […]

Building Tip of the Week: Using Zip Ties on Fuel Lines

Hey pilots, welcome back for another installment of Pete’s Tip of the Week! Only one more day until Christmas! We are excited and hope that you all enjoy a very happy holiday with friends, family, loved ones, and possibly some new toys! Today’s tip will be dealing with fuel lines and will hopefully help give […]

Building Tip of the Week: Drilling the Propeller with a Drill JIG

Hey pilots, welcome back for another installment of Pete’s Tip of the Week! Only one more week until Christmas! New toys, gifts, and hopefully new planes for all those pilots out there, and that means more new builds. Today’s tip will be dealing with the propeller and will hopefully help give you the extra edge […]

Aerobeez Customer Testimonials: Brian Chenoweth

Posted by aerobeez On April - 30 - 2015ADD COMMENTS

Customer Name: Brian Chenoweth Location: San Diego, California Feedback: This new 55″ Edge is one of the most fun planes I’ve ever had, what a blast to fly, big presence in the air and seems to do everything well. My balsa planes may start collecting dust. You will be surprised at how great that plane is! It’s pretty much all I want to fly these days. Photos: Thank you for the kind words and for your support Brian! Team Aerobeez  Read More →

Aerobeez Customer Testimonials: Lowell Hamilton

Posted by aerobeez On April - 30 - 2015ADD COMMENTS

Customer Name: Lowell Hamilton Location: Flagstaff, Arizona Feedback: It is a super easy build, even finding my own way. Thanks for the great model! Photos: Thank you Lowell for your support!  Read More →

Building Tip of the Week: Slotting CA Hinges

Posted by aerobeez On April - 30 - 2015ADD COMMENTS

Hey pilots, welcome back for another installment of Pete’s Tip of the Week! If you are not familiar with CA hinges, this tip will help you see a good way to install them and if you are familiar, we hope this helps you improve how you already install them. So without further ado, today’s tip : Slotting CA Hinges When installing CA hinges, we like to take a hobby knife and open up the slots for each hinge. This is not always necessary, but it is a good habit to get into as it will clear the... more

Aerobeez Edge540 55″ EPP Hybrid ARF Build Log Step 2 Remove the EPP foam cut outs on the bottom of the fuselage. These are precut and can be simply pressed out. These holes are pre-cut for electronics cooling. Step 4 Install the carbon landing gear with the screws provided in the hardware bag. Step 7 Remove the pieces as seen in these photos for the inserting of the horizontal stabilizer. DO NOT DISCARD the back piece! This will be glued back once the horizontal stabilizer and elevator... more

Slick540 38” EPP Hybrid Step By Step Build Log and Guide Step 2 Once your wheel and wheel pant are in position, glue the EPP cover to the wheel pant using CA or rubber contact cement. Step 4 Glue on the landing gear EPP fairings, two pieces per side. You will apply glue to one side and basically sandwich the landing gear strut. CA or rubber cement will be the glue of choice. Step 5 Remove the pre-cut EPP areas on the fuselage. You may remove all the areas as seen here or remove them as you... more

Aerobeez 93″ Extra 330 Step By Step Build Guide

Posted by aerobeez On April - 2 - 2015ADD COMMENTS

Step 2 Notice the angle of the carbon fiber main landing gear. The leading edge will be straight (pointing towards the nose of the Extra) and the trailing edge will be tapered (pointing towards the tail of the Extra.) Step 7 Use blue thread lock on the wheel collar set screws and install the wheels onto the axles. You will use 2 wheels collars per side. If you are experiencing a tight fit in getting the wheel collar onto the axle, check the inside wall of the wheel collar. There may be residual... more

The Aerobeez 2015 EPP ARF Lineup is Now Here

Posted by aerobeez On March - 21 - 2015ADD COMMENTS

Happy Friday to all the readers, flyers, and builders out there! The Aerobeez NEW 2015 EPP ARF Lineup is now here! You may have seen them at the AMA show in January, or caught a glimpse of them at the AEF, but now you can check out the finished product. We have gone through months of testing and development on our new models and created some really beautiful color schemes to show off these awesome 3D trainer EPP models! So without further ado, check them out for yourself, and we hope you like what... more

Pete and Santiago takes you for a fun flight with our 2015 SlickPro! This Slick is currently our team pilots favorite airframe! Amazing wide range of flight characteristic! 3D Huck or sport flying with crisp snap rolls and rock solid harriers! Enjoy the flight review! Some of Santiago’s points of emphasis on the model are the light weight build and build quality. Extremely light Strong frame with Carbon Fiber reinforcement Excellent aerobatic and 3D flight character   Santiago’s... more

NEW Flying Wing for 2015 In Development

Posted by aerobeez On March - 5 - 2015ADD COMMENTS

Hey everyone! What a great couple months 2015 has started off to. We have brought in our new lineup of planes and had great feedback from people at AMA and AEF with other shows lined up later this year. We have also been busy working on other new developments for one of the smaller EPP models that everyone enjoyed last year, the Aerobeez Flying Wings! We have been working with our factory to produce an improved version two of our 32″ Angry Bee and the 32″ Stinger. The designs you see... more

Building Tip of the Week: 4Titude Fuel Tank Mod

Posted by aerobeez On February - 25 - 2015ADD COMMENTS

Good day pilots and welcome to another installment of Pete’s Tip of the Week!  In today’s tip, we will be installing a 4Titude fuel tank in place of the stock fuel tank onto our Aerobeez 65″ Yak 54 Profile ARF! These same steps can also be used on our 65″ Extra 330 Profile ARF or other profile planes with some minor modifications to the process. Step 1:  Insert the long zip tie into the slots where you will be mounting the fuel tank. (this tip works great for the stock fuel... more

Aerobeez VIP Ticket 55″ Edge EPP Giveaway!

Posted by aerobeez On February - 20 - 2015ADD COMMENTS

Hey all you Aerobeez pilots, builders, and fans! Only a few more weeks until our brand NEW 2015 EPP line-up arrives. We are really excited about our two new color versions of the 48″ Extra 330SC as well as our two new models that will be joining the 2015 line-up, the 55″ EDGE 540 and the 38″ Slick 540! Both of these new models will also come in two colors. We have shown off the Yellow and Black model Edge 540 at AMA and at AEF, but there will also be a Red version! To honor the... more

Aerobeez 65″ Yak 54 Profile Step By Step Build Guide

Posted by aerobeez On February - 19 - 2015ADD COMMENTS

Yak-54 Profile Build Log Then, with a sharp hobby knife, cut away the covering for your ignition location. On the right side of the fuselage, cut away the first area in front of the main wing tube, the throttle servo slot  and the two holes directly below the throttle servo for the carbon fiber landing gear mount.  Now, locate the components to build your landing gear so that we can get this Yak on her wheels! Notice the plastic spacer is on the inside of the wheel.  The wheel collar on the... more

Building Tip of the Week: Cutting the Servo Bay

Posted by aerobeez On February - 12 - 2015ADD COMMENTS

Hey pilots, happy hump day and welcome back for another installment of Pete’s Tip of the Week! Today we will be looking at the servo bay and walking you through a simple way to cut out the skin while leaving a portion to seal the edge. This method helps prevent pealing of the skin and creates a nice clean finish. So without further ado, today’s tip : Cutting the Servo Bay When cutting out a whole in the skin for the servos, it is a good habit to leave roughly 1/8 to 1/12 of covering. This... more

BuildingTip of the Week: Installing CA Hinges

Posted by aerobeez On February - 5 - 2015ADD COMMENTS

Hey pilots, welcome back for another installment of Pete’s Tip of the Week! 2015 has been crazy busy with shows and new products, so we took a few weeks off from this series, but are happy to bring you a new tip today! If you are not familiar with CA hinges, this tip will help you see a good way to install them and if you are familiar, we hope this helps you improve how you already install them. So without further ado, today’s tip : Installing CA Hinges When installing CA hinges, we prefer... more

Aerobeez 70″ Slick PRO Step By Step Build Guide

Posted by aerobeez On January - 30 - 2015ADD COMMENTS

Aerobeez 70 “Slick Pro Build Manual Hello Aerobeez pilots and fans More Fan More Fan More Fan and welcome to Our official Step by Step build guide and manual for the 70 “Slick Pro Electric ARF kit . This manual Will Walk you through the Steps to building Our Slick Pro and Are in the order That we prefer to build. Build order is a recommendation, but it is also personal preference, so if you have experience with building and prefer to work with certain areas first or in a different order,... more

Aerobeez at the Arizona Electric Fest 2015

Posted by aerobeez On January - 29 - 2015ADD COMMENTS

Hey all you pilots out there! This past weekend was a long and busy one, but AEF 2015 brought smiles from pilots and spectators alike. This four day event hosted pilots from all around the world and some of the coolest electric aircraft around. As the Arizona sun breaks the horizon, pilots are prepping and getting ready to take to the skies. Team Aerobeez was present with Team Pilots, Pete, Santiago, and Tomas, ready to show our awesome 2015 aircraft line. Here you can see Pete and Santiago taking... more

Maiden Day with the 70″ Slick Pro Electric

Posted by aerobeez On January - 24 - 2015ADD COMMENTS

Hey friends and fans! What a great week this has been, but we have been supper busy with preparing for the Arizona Electric Fest. Before we head out to the show we were able to get the New 70″ Slick Pro up in the air for our maiden flight. It was a cold and foggy day, but we got some great pictures of the slick in action. This plane flies so smooth! Pete had it locked in and ready to hover right away. Pete Bringing the Slick Pro in for another hover!  Read More →

AMA Expo Pictures and Re-Cap

Posted by aerobeez On January - 14 - 2015ADD COMMENTS

Hello Aerobeez friends and fans! This past week we attended the 2015 AMA Expo, and boy was it a great show! This was our 3rd year in a row attending the show and this year we got some great feedback. This week, instead of posting up a new Build Blog or Tip of the Week, we will re-cap some of what went on at the show and show off some of the pictures we took while we were there. Here is a look at our plane display at the 2015 AMA Expo AEROBEEZ Booth at 2015 AMA EXPO The five new planes that we had... more

Building Tip Of the Week: Adjusting Control Surface

Posted by aerobeez On January - 8 - 2015ADD COMMENTS

Hey pilots, welcome back for our first installment of Pete’s Tip of the Week for 2015! This week has been a busy week leading up to the AMA Expo. We have been busy building our new models for the show and putting together all the final details for our new models that will be unveiled on the 9th at AMA. With so much building going on in such a short period of time, we wanted to share a simple tip to help get your control surfaces just right. Even if you don’t own an Aerobeez plane or have yet... more

Building Tip of the Week: Cowl Ventilation

Posted by aerobeez On December - 31 - 2014ADD COMMENTS

Hey pilots, welcome back for our final installment of Pete’s Tip of the Week for 2014! Tonight will be a night of celebration and we hope you all ring in the New Year with friends, family, loved ones, and possibly a new build project! Today’s tip will be dealing with cowl ventilation and will hopefully help give you the extra edge with that next build! Even if you don’t own an Aerobeez plane or have yet to take the first step into becoming an RC pilot, we want to help you improve your model... more

Building Tip of the Week: Using Zip Ties on Fuel Lines

Posted by aerobeez On December - 24 - 2014ADD COMMENTS

Hey pilots, welcome back for another installment of Pete’s Tip of the Week! Only one more day until Christmas! We are excited and hope that you all enjoy a very happy holiday with friends, family, loved ones, and possibly some new toys! Today’s tip will be dealing with fuel lines and will hopefully help give you the extra edge with that next build! Even if you don’t own an Aerobeez plane or have yet to take the first step into becoming an RC pilot, we want to help you improve your model... more

Hey pilots, welcome back for another installment of Pete’s Tip of the Week! Only one more week until Christmas! New toys, gifts, and hopefully new planes for all those pilots out there, and that means more new builds. Today’s tip will be dealing with the propeller and will hopefully help give you the extra edge with that next build! Even if you don’t own an Aerobeez plane or have yet to take the first step into becoming an RC pilot, we want to help you improve your model building, set-up,... more

Building Tip of the Week: Prepping a Fuel Tank

Posted by aerobeez On December - 10 - 2014ADD COMMENTS

Hey pilots, welcome back for another installment of Pete’s Tip of the Week! We took a week off for the Thanksgiving holiday, but now we have a new tip for those December builds out there! These tips will help give you the extra edge with that next build! Even if you don’t own an Aerobeez plane or have yet to take the first step into becoming an RC pilot, we want to help you improve your model building, set-up, and eventually flying skills. So without further ado, today’s tip will focus on: Prepping... more

Aerobeez 89″ Sbach 300 Step By Step Build Guide

Posted by aerobeez On December - 3 - 2014ADD COMMENTS

89″ Aerobeez Sbach300 Build Log Step 5 Using blue thread lock on the wheel pant screws and install the fiberglass wheel pants to the carbon landing gear.  Note:  The “blind” nuts are preinstalled in the fiberglass wheel pants. Step 6 Adjust the wheel collars to center your wheel in each wheel pant and tighten the collars. Step 9 Before we install the tail gear assembly, we will install the rudder to the vertical stabilizer.  Use a drop of household oil in each of the... more

Building Tip of the Week: Applying Decals

Posted by aerobeez On November - 26 - 2014ADD COMMENTS

Hey pilots, welcome back for another installment of Pete’s Tip of the Week! With Thanksgiving only a day away and Christmas just around the corner, there are likely some model building days in store! These tips are just the thing you need to help with that next build! Intended to help with all types of model building, these tips will help take your building to the next level. Even if you don’t own an Aerobeez plane or have yet to take the first step into becoming an RC pilot, we want to help... more

Building Tip of the Week: Engine Stand Off Set-Up

Posted by aerobeez On November - 20 - 2014ADD COMMENTS

Hey pilots, welcome back for another installment of Pete’s Tip of the Week! Gearing up for the festive holidays and prepping a new build during the cold winter ahead? These tips are just the thing you need to help with that next build! Intended to help with all types of model building, these tips will help take your building to the next level. Even if you don’t own an Aerobeez plane or have yet to take the first step into becoming an RC pilot, we want to help you improve your model building,... more

Flying Wing Step by Step Build Guide Pro Set-Up

Posted by aerobeez On November - 13 - 2014ADD COMMENTS

Hello pilots and builders and welcome back to another installment of our Step By Step Build Guide series! In this build log, Pete will show the different methods that can be used in building the Aerobeez fun wings. This is a modified Pro Set-Up that shows off some of the ways that you could improve or mod the basic set-up. Certain parts that come with the receiver ready kit will not be used to save weight and improve performance. These flying wings are completely customizable to your own preference. So,... more

Building Tip of the Week: Marking the Servo Bays

Posted by aerobeez On November - 6 - 2014ADD COMMENTS

Hey pilots, welcome back for another installment of Pete’s Tip of the Week! We took a week off last week from the tips portion of our blog, but now we are back with another great tip for your builds. As always, these tips are intended to help with all types of model building, even if you don’t own an Aerobeez plane or have yet to take the first step into becoming an RC pilot. We want to help you improve your model building, set-up, and eventually flying skills. So without further ado, today’s... more

Aerobeez 89″ Yak 55 Step by Step Build Guide

Posted by aerobeez On October - 29 - 2014ADD COMMENTS

Hi Pilots!  Welcome to our hands on Step by Step Aerobeez 30% YAK-55 build blog!  This is a Pro build by our team pilot Santiago Perez.  As always having experience with putting an ARF together is good, but with our guide even an inexperienced builder should be able to put this kit together in about 10-12 hours. Look for “Pro Tip’s” that are unique tricks and tips called out by Santiago Perez and our notes that will help walk you through this build like a seasoned pro. These... more

Building Tip of the Week: Prepping the Servo Bays

Posted by aerobeez On October - 22 - 2014ADD COMMENTS

Hey pilots, welcome back for another installment of Pete’s Tip of the Week! As always, these tips are intended to help with all types of model building, even if you don’t own an Aerobeez plane or have yet to take the first step into becoming an RC pilot. We want to help you improve your model building, set-up, and eventually flying skills. So without further ado, today’s tip will focus on: Prepping the Servo Bays On your servo bay installations, it is always best to drill 1/16 pilot holes.... more

Building Tip of the Week: Pull/Pull Rudder Wire Set-up

Posted by aerobeez On October - 16 - 2014ADD COMMENTS

Hey pilots, welcome back! This week we have a bonus installment of Pete’s Tip of the Week. As always, these tips are intended to help with all types of model building, even if you don’t own an Aerobeez plane or have yet to take the first step into becoming an RC pilot. We want to help you improve your model building, set-up, and eventually flying skills. So without further ado, today’s tip will focus on: Pull/Pull Rudder Wire Set-up Before installing your Pull/Pull rudder wires and servo,... more

Hello Aerobeez Pilots! Welcome back for another installment of Pete’s Tip of the Week. As always, these tips are intended to help with all types of model building, even if you don’t own an Aerobeez plane or have yet to take the first step into becoming an RC pilot. We want to help you improve your model building, set-up, and eventually flying skills. So without further ado, today’s tip will focus on: Installing Control Surface Horns Prior to gluing any control surface horns, Pete will always... more

Hello Aerobeez Pilots! Welcome back for Octobers first installment of Pete’s Tip of the Week. As always, these tips are intended to help with all types of model building, even if you don’t own an Aerobeez plane or have yet to take the first step into becoming an RC pilot. We want to help you improve your model building, set-up, and eventually flying skills. So without further ado, today’s tip will focus on: Installing Self Tapping Screws. When installing any screws that are “self tapping”... more

Aerobeez 71″ Extra 330 Step by Step Build Guide

Posted by aerobeez On October - 2 - 2014ADD COMMENTS

Hello Aerobeez Pilots and welcome to our 71″ Extra 330 Build Guide! As with our previous build guides this guide will walk you through step by step as you build your new 71″ Extra 330 ARF Kit. Having experience with putting an ARF together is good, but with our guide even an inexperienced builder should be able to put this kit together in about 10-12 hours. Look for “Pete’s Tip’s” and our notes that will help walk you through this build like a seasoned pro.  This... more

Building Tip of the Week: Installing Pivot Style Hinges

Posted by aerobeez On September - 25 - 2014ADD COMMENTS

Hello Aerobeez Pilots! Welcome back for another installment of Pete’s Tip of the Week. As always, these tips are intended to help with all types of model building, even if you don’t own an Aerobeez plane or have yet to take the first step into becoming an RC pilot. We want to help you improve your model building, set-up, and eventually flying skills. So without further ado, today’s tip will focus on: Installing Pivot Style Hinges. When gluing in pivot style hinges, always use a drop or two... more

Hello Aerobeez Pilots and welcome to our Aerobeez 20cc Sbach Profile installment of the Step by Step Build Guide series.  This build log will provide the steps that our team pilot, Pete, uses for this build.  You can cross reference with the included manual on the CD disc at anytime.  Also we will include Pete’s Pro Tips for certain steps that will help along the way.  Please keep in mind with this Sbach Profile, certain steps may be changed for your personal build preference and equipment... more

Building Tip of the Week: Wicking the Motor Box

Posted by aerobeez On August - 27 - 2014ADD COMMENTS

Hello Aerobeez Pilots! Welcome to the our 3rd installment of Pete’s Tip of the Week. These tips will help with all types of model building, even if you don’t own an Aerobeez plane or have yet to take the first step into becoming an RC pilot. The intention is to help you improve your model building, set-up, and eventually flying skills. So without further ado, today’s tip will focus on: Wicking the Motor Box. This tip will significantly assists in the overall strength of the motor box and any... more

Building Tip of the Week: Nut and Bolt Installation

Posted by aerobeez On August - 13 - 2014ADD COMMENTS

Hello Aerobeez Pilots! Welcome to the another installment of Pete’s Tip of the Week. These tips will help with all types of model building, even if you don’t own an Aerobeez plane or have yet to take the first step into becoming an RC pilot. The intention is to help you improve your model building, set-up, and eventually flying skills. So without further ado, today’s tip will focus on: Nut and Bolt Installation. When you are trying to install nuts in various areas where it is difficult... more

Building Tip of the Week: Blue Thread Lock

Posted by aerobeez On August - 6 - 2014ADD COMMENTS

Hello Aerobeez Pilots! Welcome to the first installment of Pete’s Tip of the Week. Even if you don’t own an Aerobeez plane or have yet to take the first step into becoming an RC pilot, these tips will help you improve your model building, set-up, and eventually flying skills. So without further ado, today’s tip will focus on: Blue Thread Lock. Always try to use Blue thread lock on all the machine screws when a “lock nut” is not being used on the opposing side.  Blue... more

Aerobeez Summer Contest & Giveaway

Posted by aerobeez On August - 1 - 2014ADD COMMENTS

Thank you everyone for giving us so much feedback on our Aerobeez ARF Summer Contest. You have spoken and we listened. We would like to get everyone of all ages involved in our passion. To enter STARTING AUG 1ST, simply… Step 1. Make a fan sign (of any size) and take a picture of yourself that shows your support for Aerobeez with the sign. Step 2.  Post the picture to our time line on Facebook. Like our page if you haven’t already so that you can follow the contest. Or Post a your... more

Aerobeez 73″ Sbach 300 Step by Step Build Guide

Posted by aerobeez On July - 23 - 2014ADD COMMENTS

Hello Aerobeez Pilots and welcome to our 73″ Sbach 300 Build Guide! Like the previous two articles this build guide will walk you through step by step as you build your new 73″ Sbach 300 ARF Kit. Having experience with putting any ARF together is good, but with our guide even an inexperienced builder should be able to put this kit together in about 10-12 hours. Look for “Pete’s Tip’s” and our notes that will help walk you through this build like a seasoned pro.... more

Aerobeez 74″ Slick 540 Step by Step Build Guide

Posted by aerobeez On July - 15 - 2014ADD COMMENTS

Hello Aerobeez Pilots and welcome back! In this article we will walk you through step by step as you build your new 74″ Slick 540 ARF Kit. If you have experience with putting any ARF together, this build should take you about 10-12 hours to finish. Even if this is your first ARF build, our tips and tricks will help walk you through like a seasoned pro. Here is what the 74″ Slick 540 will look like once complete! Step 1.2:  Locate the landing gears, wheel pants, and landing gear axles... more

Aerobeez 73″ Yak 54 Step-By-Step Build Guide

Posted by aerobeez On July - 9 - 2014ADD COMMENTS

Hello Aerobeez Pilots and welcome to our 73″ 25% Yak 54 build guide. In this article we will walk you through step by step as you build your new 73″ Yak 54 ARF Kit. If you have experience with putting any ARF together, this build should take you about 10-12 hours to finish. Here is what the 73″ Yak 54 will look like once complete! Note: The rudder gap and hinges once glued should look like the example image shown here. Step 2.5:  Install the tail wheel assembly.  Note:  For... more

In this article we will show you a step by step build process of the Aerobeez 48″ Extra 330 EPP.  This plane is made for extreme 3D flight, yet with an EPP skin this plane is virtually maintenance free.  And setting it up is a breeze.  If you have experience with putting any ARF together. This build should take you no more than 2-3 hours to finish. NOTE: The frame pictured in this build is of an older scheme, but all of the steps are the same on our new kit. Wing retainer hooks have been... more

We are excited to introduce our first flying wings–Angry Bee and Stinger.  Each color scheme has two versions–Push Prop & EDF.  In this build review, we are going to go over how to put together the push prop version. And we are using the Angry Bee for this build. This kit is so easy to put together, since the motor box is already assembled. And the servos slots are already cut out. If you are a fast builder, it would only take you 1 hour (including the time for the glue to set)... more

I started one morning with the intent of a complete build of my Aerobeez 26% Slick 540 ARF and maiden the next day! Keep in mind this ARF includes all the hardware and a plumbed ready fuel tank! As I took the parts and components out of the box, I noticed the attention to detail in where each airframe piece was placed and taped in the box. Everything was super secure and the main box was very thick. I laid out my basic build tools a cup of coffee and my build begins. So super excited to get the... more

Maiden Day for the new 30-35cc Slick540!

Posted by Pete On November - 4 - 2013ADD COMMENTS

Got to the field early morning around 8:30.  Couldn’t sleep much the night before as I was so super excited about the maiden flight.  I’m sure all you pilots know the feeling!  The day was overcast and chilly as I assembled the Slick540 with main wings.  Let’s back track a bit.  The morning starts off with me forgetting something at my workshop.  As I pulled into the field, I had to turn around and go home to pick up an important part I forgot.  Now back to the ready to control... more

Maiden Day of our new 30% Slick540!

Posted by Pete On October - 16 - 2013ADD COMMENTS

The day started actually the night before with me prepping the new Aerobeez Slick 540.  Tuning and making sure all the programming is correct, checking and checking again all the screws, bolts, and fasteners.  You can never be too safe with a giant scale airplane!  I am building this Slick 540 to be HUCKED!  Checking all the XQ Power servos for correct travel amounts and setting all my rates/expos for the Miracle Arms.  Time to go to bed… can’t sleep!  Visions of torque rolls, pop... more

Team Aerobeez Fun Day out flying with the Pros!

Posted by Pete On October - 12 - 2013ADD COMMENTS

Couple weekends ago we spent the day out at the Apollo Field with a few of our pro pilot friends!  There was non stop laughing and fun while hucking a few Aerobeez ARF planes.  During the day we tried all the standard 3D maneuvers on our new 30cc Yak-54 with DLE-30 motor and even invented a few new ones (horizontal pop-top/pinwheel) that we thought would break the wings off! Aerobeez Team pilot Santiago checking the Yak 54 before flight Check out some videos from the event here: We also had a... more

Aerobeez Weekly Photo Contest!

Posted by aerobeez On May - 16 - 2013ADD COMMENTS

Occasionally we get emails from customers with photos of our products. And we very much appreciate them doing so.  But then we realized that there may be lots of beautiful pictures from all our customers that are not being seen. So we want to start this contest to encourage you to show your nice photos of our planes, and reward you for them. We give out prizes every week. This week’s prize: See here for the official rules: http://aerobeez.com/photo-contest.html Here are the rules: Photo... more

About Me

Stationed in California, we are a developer and distributor of RC plane products. Our mission is to get more people to enjoy the fun hobby of RC flying by offering good quality RC planes at an affordable price. Our company is formed by a group of airplane enthusiasts who love to be around airplanes. We carry the products we like and we want to offer them at a reasonable cost so hopefully more people will enjoy them as much as we do. We believe in good customer service. We want to provide the necessary support to our customers so they can start to enjoy our great products in the shortest time possible. As we are constantly looking for ways to improve our products and service, we love to hear from you. Please feel free to give us your feedbacks and suggestions.

Web Site: www.aerobeez.com
Email: support@aerobeez.com
Phone: 877-813-5337






Follow Me on Pinterest